- The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel.Be sure to bleed the air and refill the fluid in the MASTER after replacement.Th...Прочитайте больше
- ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. ...Прочитайте больше
- It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to b...Прочитайте больше
- CYGNUSxInitial Model (SE12J), if it's the same Caliper model, this The product fitsI couldn't find anything that looked like a match and it was a no-go, but it was OK with no problemsIt is recommended...Прочитайте больше
- I used it in a Tokico 6-pot, and since the Screw was with me, I figured I could use it! Brake fluid leaked and it was Large Please be careful There is no problem in the productПрочитайте больше
- The shape of the tip is slightly different from OEM. I feel a sense of incompatibility when I put on Rubber cap.Seal tape winds in the reverse direction, not in the tightening direction.Noticing that ...Прочитайте больше
- Noticing that Brake fluid seeped out of Caliper's Air breederRust was amazing as I removed it. Indeed when I thought this was dangerous, I found this productReplaced. As I wrote that the installat...Прочитайте больше
- Previously, there was no tool to match when brembo's MASTER, Caliper air bleeding tried, and there was a memory to go buy. By changing to Breeder here, it will be 10 mm Box so you can make it with...Прочитайте больше
- Because it rusts as soon as iron, Material : I purchased Stainless Steel. We are solidly making details, we are satisfied with Large change. I am happy that it's a bit cheaper.Прочитайте больше
- I bought it because I wanted to replace SEM's Air breeder from OEM for Front caliper OH. It is measures against rust.Once, I sealed it and assembled it.Прочитайте больше
- 【What made you decide the purchase?】OEM's RadarBolt was rotten w【How was it actually used?】Cool at One point【Mounting was difficult?】Just replace with OEM【Please tell me the installation point and...Прочитайте больше
- It was used for the SEROW225 WE.Although there was no leak at the time of OH of the Front brake, since rust was conspicuous with degradation also in model, it exchanged. Since it changed, brake perfo...Прочитайте больше
- Since the vehicle type had rusted, the hornet250(98')authentic positive Breeder did simultaneous exchange of it at the thing made from a STAINLESS STEEL which does not rust easily at the time of Fluid...Прочитайте больше
- It is good that a 10-mm Glasses was able to come to chip by the Size having been set to M10.
is especially common.
About the rust prevention by having become a STAINLESS STEEL.
It is high anyhow...Прочитайте больше - As for the Brake and the Clutch, the Breeder also treated the product made from a STAINLESS STEEL of the DAYTONA to the occasion which replaced the MASTER to the brembo.
Together with the order Cal...Прочитайте больше - Since a part of BREMBO Caliper authentic positive in BMW and Breed valve of the Clutch were One way valves for fixtures at the time of Manufacturer Line manufacture (Blind Plug sealing), all were exch...Прочитайте больше
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА