- XR250MOTARD, used for front and rear Blinker LEDs.It did not work well.Specifically, I have become a high flasher.Honda's Front blinker seems to be a bit special as it also serves as a position.Прочитайте больше
- I had bought another Relay before to replace the Tail Lamp LED, but it broke and made a cracking sound when I fell down or did something to it. I thought it would be better to buy the same one, so I b...Прочитайте больше
- [How is it used?HondaFTR223 (Past)KawasakiD Tracker (Past)KawasakiZ400 (Installed this time)Used in the above 3 car models.I have purchased three times because I personally felt the quality was good.F...Прочитайте больше
- I installed a LEDICRelay made by MOTO LED and the Blinker did not respond.The other day, when I installed DRC's LED Fender Eliminator Kit, KITACO's Unbreakable lensMini Blinker on the front and rear o...Прочитайте больше
- I bought this to use on my WR250F, but I didn't read the instructions carefully and ended up not being able to use it ……It's a product I didn't have to buy because it worked fine without this ICRelay ...Прочитайте больше
- After replacing the valve, it was not reacted by SW ON Yellow light upside down, front and back lit up. I think it's defective. And I turned it back on flasher status. Will you replace it?Прочитайте больше
- CRF250L mugenSpec. Mounting on.For the company's LED Blinker back and forth installation, we replaced it.You can remove the RightShroud and access it, but it took time to install it. (Somehow inst...Прочитайте больше
- CRF250L (MD44) It installed in.Unlike MD 38, the installation location of Blinker relay is different, I thought that Wiring would be a little longer.Since it can not be mounted close to Injection, pro...Прочитайте больше
- Mounting on KDX125SR.Since KDX 125 is 12 VDC after A 2, it is easy to make Blinker LED.Compared with other companies the price is cheap and easy to use.Since KDX employs a system in which front and re...Прочитайте больше
- I purchased Blinker, Fender Eliminator and ICRelay.First I think that it will be High flasher with only Blinker and Fender Eliminator attached.Actually tried!I think that it is better to buy at the sa...Прочитайте больше
- Since Standard's Blinker was damaged, I exchanged it to Blinker of DRC, but in Relay of Standard, the High flasher phenomenon occurred, so I exchanged this Relay.After exchange, High flasher pheno...Прочитайте больше
- I also write other people, but I can not even pinpoint Wiring because it is difficult to understand.I stopped it with Tie Wrap at the place where I removed the original Relay.Also, it does not have an...Прочитайте больше
- This DRC's MOTOLED LED IC Relay is a necessary part for exchanging STD Blinker of Light bulb Valve with LED Blinker.In NORMAL 's AnalogRelay, it is a Relay made to operate properly with the cu...Прочитайте больше
- I installed it to change to LED Blinker.It was easier to change ICRelay without adding anything to BlinkerWiring everywhere, so I chose this.Special installation is not difficult, I could install with...Прочитайте больше
- In the product Instruction Manual, the Black wire is connected to the car body,Although there is description that it seems to take Earth from the car bodyI had to connect directly to Minus side of Bat...Прочитайте больше
- 【What made you decide the purchase?】In order to install the LED Blinker, I purchased it because I had to change Relay.The price was also relatively cheap became the deciding factor of purchase【How was...Прочитайте больше
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА