- [How is it used?YAMAHA XJR400R (07 year) The purchase was made in conjunction with the conversion to Separate handle of theIf NAKED is made into a separate handle, the handlebar may hit the tank or pi...Прочитайте больше
- I purchased a Kawasaki Zr-7S to convert to Separate Handlebars.NORMAL is Handlebar Up Type, so if it is made into Separate Handlebars, it will surely hit the Tank.A Handlebar Stopper is required to co...Прочитайте больше
- Purchased for use with the GSX-R125.The installation was ExactlySize without any modification.I put it on for circuit driving, but of course it reduces the angle of turn and I can't lock the handlebar...Прочитайте больше
- [How is it used?I bought this bolt to prevent the cowl from interfering with the handlebar on my Ninja 400. The supplied bolt is not long enough so I bought a 55mm bolt and installed it.Was the instal...Прочитайте больше
- I bought this for my TZM50 but I couldn't install it.It is a spec. that fits into the NORMAL Handlebar Stopper welded to the frame.The width of the groove is insufficient for the thickness of the Hand...Прочитайте больше
- I use it because I'm afraid of getting my hand caught in the Handlebar.Прочитайте больше
- I think this is a standard product of Handlebar Stopper.I use it on my NSRmini and KX65.Both of them can be installed without any processing.It is better to check it once in a while that the screw loo...Прочитайте больше
- As the product name suggests, the cutting angle of the Handlebar becomes Small by mounting it.Installation EffectPrevents your hand from getting caught between the Handlebar and the Tank during an acc...Прочитайте больше
- I bought it because I had to control the angle of cut due to a change in Stem.It was installed on a vehicle that was not listed in the fitment column, but there was no problem.Even the thickness of th...Прочитайте больше
- My boss suggested I buy it, but I didn't even know such a product existed.Separate handle, so that the Handlebar hits the Tank. But now that I have this product, I don't have to worry about hitting th...Прочитайте больше
- It was diverted to GPZ 1000 RX under Racerization.When Stem was changed to ZrX 1100, the cutting angle of Handlebar was Large ruffling, and I made a dent in Tank when I fell down.Of course there is al...Прочитайте больше
- It has a shape that does not change from old days, and it is easy to install, so I am using it.It is shaped to be sandwiched between the Handlebar Stopper, so it can not be attached to the deformed Ha...Прочитайте больше
- We are attaching to the first half of NSR 50.When exchanging with outside company's Separate handle, we installed Handlebar to interfere with Tank. Installation can take less than 5 minutes.I can ...Прочитайте больше
- I installed Circuit because I am driving. It was easy to install with Bolt-on and the Instruction Manual was also polite. Until now I cut my handlebar full of duties and it was dangerous to hit Cowl, ...Прочитайте больше
- Because Normal handle has protrusions to fix Position on Top Bridge, attaching this Handlebar Stopper eliminates the possibility that Handlebar will hit the tank when falling. After Cableetc around Ha...Прочитайте больше
- It is not for RZ 250, but it was possible to install. Some processing is necessary. We scraped out and spread in the place to enter with File, Bolt alone stops with Body's Receptacle screw but it ...Прочитайте больше
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА