* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
A design which does not break down the style of a motorcycle in the state where the back is not followed, either is wonderful! Since it supports again so that it may not involve in firmly when a back is attached, he can feel easy very much! The texture of
A design which does not break down the style of a motorcycle in the state where the back is not followed, either is wonderful! Since it supports again so that it may not involve in firmly when a back is attached, he can feel easy very much! The texture of plating is also high-quality and wonderful!
I prefer the simple design of the old W1Type OEM shape if possible, but this is a design that has been around for a long time, so I'm convinced to use it The support bar is in a good position and it protrudes moderately so that it can be used with the Tire wheel There's no need to worry about bag entrapment as there's a space in between Easy to install, not badly accurate, but in my case Quantity:Pair (for Left and Right) One of the locations was installed with a bit of a pull Once installed, it can be fixed firmly, the appearance is not bad, and there is no sense of discomfort even without the Bag It is not The same support is also sold by DAYTONA, but the side support The bar made by KIJIMA is in a position above the DAYTONA one (I think it's more of a visual difference than bagging.) Quantity:Pair (for Left and Right) When it comes to installation, I'm still not sure if the cost performance is good, here Plating Specification, etc., although it may be difficult to get a price for the processing For safety reasons, I think the SIDE/Saddle Bag must be fitted with a support system It is (There are other Ideas besides the support bar, but...) View Detail
Right and left were purchased.The Parenthesis of appearance is [ both of directions ] good if it sees from back.The Bolt of the Sas upper part did not escape from left-hand side unexpectedly, and attachment had a close game, although right-hand side was easy.Since until falls out to some extent, if it does pulling to the way which extracts a hidden Washer with Plierses etc. while turning a Wrench, it will be easy to extract the rest.It entered, when putting in, and the Bolt was put in, after carrying out kiln, raising lightly under the Swing arm using the Jack for cars and putting a hole together, since the hole of the Frame does not suit Sas.View Detail
It purchased simultaneously with the object for right-hand side.Since it is goods which are not symmetrical, there is no compatibility the object for right-hand side and for left-hand side.
When carrying out a Tandem, if a fellow passenger's calf hits this Saddlebag support was worried, but it does not hit in the usual riding posture.: which is quotation from the Impression for left-hand side in below
it equipped for interference with the Rear suspension at the time of using a Side bag, and the involvement prevention to a Tire.It is a Beauty, and a Plating does not spoil the whole appearance Balance in the state without a Side bag, either, but is good touch.Where a Center stand is stood about single-sided 15 minute, it equipped with > working hours.When letting the Bolt of a Rear-suspension portion pass, the hole with a Frame shifted, and a Bolt did not pass, but it got impatient, but it succeeded by letting a Bolt pass, raising a car body.Although used together with
and a Rear carrier, die length was not necessarily insufficient with an especially satisfactory pure Bolt.View Detail
A design which does not break down the style of a motorcycle in the state where the back is not followed, either is wonderful! Since it supports again so that it may not involve in firmly when a back is attached, he can feel easy very much! The texture of plating is also high-quality and wonderful!View Detail
They fit fairly easily with the Kijima pillion rail. The overall appearance is really good, definetly not strong enough to carry a pillions weight-so make sure your pillion understands this first rime they get on the bike. I originally had a different grab-rail installed, but it simply wasn't compatible with this product despite first appearances. Hence why I switched to the Kijima pillion rail.View Detail
High quality. perfect fitBuy the rear rack to go witheasy to installGreat valuefast shipping. got it in a few daysI draped a thin sheet over rear fender to keep from scratching during install. View Detail
Ordered the part in the US and it arrived on time. The support itself is fairly sturdy and was quiet easy to install, takes around 30mins for install.View Detail
Installation was easy, hold my side bag very well. Paint finish looks like OEM and fit my W800 cafe perfectly. Would recommend purchasing a pair.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА