* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
It was used when attaching Barrel 4 of DELTA to a SEROW250.Since in the case of the SEROW a Gasket is attached to a Normal silencer and it Says, this is removed and reuse is difficult. It is easier in the case of NORMAL return to leave rat
It was used when attaching Barrel 4 of DELTA to a SEROW250.Since in the case of the SEROW a Gasket is attached to a Normal silencer and it Says, this is removed and reuse is difficult. It is easier in the case of NORMAL return to leave rather.although it is almost equivalent in (although not returned)
thing being pure -- the Barrel 4 side side and the Exhaust-pipe side -- -- it was slow.(Individual specificity ?) Since there seemed to be no problem when fastening, but it was a sense and it hard to work, heat-resistant Gasket was applied thinly and it fixed.There is no exhaust leakage as a result of . It is although it is natural and becomes empty.
Thank you, WEBIKE! I didn't think I would ever find the right part. This exhaust joint gasket fits the Delta Barrel 4 Exhaust. I didn't have a caliper to measure the exact fit of the exhaust joint and they smash after use. So I didn't know the actual size I needed. It was proving quite difficult. My exhaust wouldn't fit without it. I now have it am I'm very pleased with the product. Thanks again, WEBIKE.View Detail
I bought this product because my XR250MOTARD was leaking gas from the joint gasket and it was bothering my neighbors. the KITACO product was cheaper, but I wanted to stop the leaking completely and it was highly rated, so I bought this one.
As an advise, you can apply grease to both the inside and outside of the joint gasket with a cheap oil-based product. This will make installation easier, increase efficiency, protect the gasket, and also seal the gasket against gas leaks as the grease will burn off with heat after installation.
The most common mistake is to modify or cut the gasket because it is difficult to fit. It depends on the material.
If you have a Slip-on Silencer, you can use a pliers tool to widen the Silencer side so that the joint gasket can fit. If it is a Slip-on Silencer, you can use Pliers etc. on the Silencer side to widen the joint gasket to fit.
Most of the time, the gasket doesn't fit well on the external silencer side, so the gasket is damaged by forcing it to fit.
The Gas leak stopped completely and I was very happy with Large.View Detail
I bought it again because it was new and somehow it got into the back of the MiddlePipe. I've bought JMCA Certified for places where I can't run without changing the exhaust system many times, but the quality is usually fine.View Detail
I installed it in the OEM joint of KLX250SR The outer diameter was Exactly, but the inner diameter was too big and there was no space between the clamps no matter how much you tighten the clamps It felt like it was going to be empty, so I dealt with it by applying liquid Gas to it stiffly It's a good thing that the tip of the pipe is plugged in, so it's a large and sturdy pipe without liquid gas It may be, but again, if you want to use it for this motorcycle, you need to use the Recommendation I can'tView Detail
I bought it for when I removed and adjusted the Exhaust System in spring and adjusted it afterwards. The product will be purchased for the third time. There are BALI on the cut surface, but it is acceptable range. I always find it useful.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА