be absorbed -- it will choose and will be satisfactory.
It is a product without a complaint.
be absorbed -- it will choose and will be satisfactory.
* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей.
* Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения!
* Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
5 / 5
1 Обзор
rating breakdown
5 Stars | 1 | |
---|---|---|
4 Stars | 0 | |
3 Stars | 0 | |
2 Stars | 0 | |
1 Stars | 0 |
It is a product without a complaint.
be absorbed -- it will choose and will be satisfactory.
Fits: SUZUKI SV650X 16-21, SUZUKI SV650 16-21
I needed some spools to lift the rear of my Suzuki SV650 with my race stand for maintenance and this product served that purpose with the added bonus of also protecting the motorcycle in the event of an accident.View Detail
Fits: KAWASAKI NINJA400 (2014-) 14-17
I had it mounted onto my motorcycle when it was still brand new. Just as I suspected, I had a fall when driving at high speed with the motorcycle that I wasn't yet used to at the time. It was scratched hardly but the engine had no damage. I left it scratched more than 10 years and decided it was a good chance to replace it with a new one. The instruction for use is written in hand writing and is inconsiderate. Well, I was lucky to know what to do. The spring washer was also out of stock. The one I got years ago had mounting holes located in the wrong position and I had to get holes opened, but this time they were in the right position. It might have improved. Also a rubber plate is attached to the mounting section. It maybe for anti vibration. The mounting screws have changed from black screws to plated screws. Guess they have improved during the years gone by. When mounting, you have to hold the engine with a jack to remove mounting screws. Also you'll need a long extension bar and universal joint to tighten the screw on the front left side because the exhaust pipe will get in the way.View Detail
Fits: KAWASAKI NINJA400 18-21, KAWASAKI NINJA250R 18-21
It's easy to install and when using the Maintenance Stand, it's nice and stable, but
Normally, I would have preferred to go a little smaller because it would have been unnecessary to stand outView Detail
Fits: KAWASAKI NINJA400 18-21, KAWASAKI NINJA250R 18-21
It looks like a Small Slider
It's a simple shape, but it's a nice touch
In terms of performance, because it rotates like a roller, it is
When using the Maintenance Stand
Raising it is more than the normal MaintenanceBolt I used to use before
It's easier to raise itView Detail
Fits: KAWASAKI ZrX1200ZrX1200 DAEG 09-16
I bought this because I wanted to get the type with slider function It was able to install with no problem, but I used ZrX1200 for JTripSTAND and JTripZrX Please note that you cannot use Bracket if you are using a receiving Bracket and Slider hits and I can't lift up I bought this without any hesitation because the fitment for each car model was available, but I didn't think there was such a pitfall It was It's certainly not a problem to fit it, so it's fitfully malleable, but it failed... I drove it into the wall of the Garage I made it into a hat rack with LOL!View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
Чтобы продолжить просмотр данной продукции на веб-сайте Webike для японского рынка (на японском языке), нажмите кнопку "Перейти к Webike в Японии".
Клиентский сервис
ИНФОРМАЦИЯ
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА