855.65 RUB
(1,400 иена)
706.52 RUB
(1,156 иена)
(17% OFF)
4 (4 Отзывы)
Very Good
SEROW 225 WE requires processingOEMHorn of SEROW 225 WE was rusted and replaced so it changed.
SEROWOEM 1 of 12 V. It's Horn of 5 A, but the sound is a bit small. Therefore, it will be replaced with another company product that has a relatively loud volume, purchase this.
There is one problem, this Horn terminal is vertical, SEROW 225 does not stick like this.
For that, it is necessary to bend the terminal. It can be done with MONKEY Wrench. Let's be careful as you break too much.
By the way Bracket diverted OEM. It is good to make the position to be slightly diagonal. People who want to use the new one are durable Large.
The volume is also good slightly higher than the OEM feeling.
Reviews For DAYTONA Рог 12V From Other Webike User
Excellent
Quality as well as OEMMotivation
The OEM was functionally OK, but it was Black Painted over rust, so it looked I bought it for the Refresh of
[Why Daytonahorn?
The OEM Product was discontinued and KIJIMA and POSH etc. were considered, and the OEM Product was made in Black (8 cm in diameter) and the same size as the OEM sound by searching for the sound of the Horn of each company We chose this product as a
Installation
If you want to replace the OEM bracket with this product, please use the OEM bracket Installed
The OEM Bracket is in a state of rust as well as the body, so after hanging the paper, it's ready to be used Black Painted and mounted
BracketSize is one size larger than OEMRubber, so OEMRubber I stuffed the packing to prevent it from falling and installed it
[Sound Quality]
Originally, I bought the GPZ1100 OEMHorn as a close sound because it didn't sound bad It is almost the same sound
[Others]
As a Universal Product, it has the same quality as the OEM Product, and it has the same quality as the OEM Product I'm very happy with the low price
View Detail
Very Good
Large sizeI installed it in DT230 LANZA I think that Horn that had originally arrived had deteriorated or the volume was sounding too small They didn't notice it, so I decided to replace it at my own peril, but when it arrived It's a little bit larger than OEM, and it was decided to install it after some thought With the Horn, the place to attach the Connector is on top, but with this Horn, it interferes with the So I adjusted the position of the attached bracket and installed it horizontally As a result, it was possible to wear it without interfering anywhere, so it was good, but I installed the Connector sideways The waterproof property is a little doubtful because it has become a little bit I'm a little worried about that because it got bent Well, I think that Large is strong
The volume is a satisfactory Level It's not too loud, but almost like a normal horn But the tone is a little muffled and a little out of tune LOL Some people might be bothered by thisView Detail
Most Viewed Reviews Of DAYTONA Horn
Very Good
Horns PoshBeautiful, fit formy motorcycle kawasaki w800 ,low price But the sound is light.the chrome is pretty and it's more like a motorcycle.View Detail
Very Good
It is made in Taiwan.I bought this because my KSR2 OEMHorn stopped sounding.
You can buy a new one for the same price as OEM used one or less, so I think the cost is very high.
There is Horn made by other companies in the same price range, but I chose DAYTONABrand of safety and trust because it is the one which cannot be disassembled and repaired basically when the inside breaks down like this time.
The Package includes MADE IN TAIWAN and I personally trust them more than products made in China or other Southeast Asia countries.
The material is iron, but the surface is coated with thick plating.
KSR Horn is DC, so I could use it normally.
I think it is seldom, but I haven't confirmed whether it sounds when Horn is AC.
There is a nave screw for the adjustment of the example on the reverse side, but it is not written in the instruction manual. Don't spin it, it'll break. It is stated that
At any rate, there was no problem in the use with the sound quality as it was without touching anything.
It is unconfirmed whether it is possible to adjust it by turning Screw when it stops sounding due to aging or whether it is really damaged if you turn Screw.
In the case of the KSR, remove the 2nd oil tank and work on it.
However, if you remove only one of the two screws from the oil tank, the other screw hole will be overloaded and may break.
By the way, OEM new products of Oil tank have been discontinued.
The OEM bracket has a rubber damper to prevent vibration, but the screw length of HornBody is too short to use it.
If the neck is long, it may become severe in terms of space depending on the type of car, but even the Spring washer of the loosening stopper was difficult to insert, so I thought I would like to set the screw longer by 5-10?
In the meantime, I'm tightening it up.
We have already installed the countermeasure regulator on our KSR, but we were able to install it without any problem.
As for the Nut of Reverse side, there was Space that tightened without a problem with the Twrench of normal Size by removing the Shroud of Right Side.
Because of its location, it is exposed to rain and mud, so I cleaned the terminals well and applied Contact Grease before installing.
The sound quality is larger and thicker than OEM Horn, and it became about a light car.
Horn, which is seldom used but is quite impatient when it doesn't ring at the time of need, can be firmly claimed, and I am satisfied.View Detail
Other Reviews From Japan User(translated)
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА