I was looking for Tale lamp for expansion of Motorcycle variously with Net, Motorcycle parts Shop, etc., but after all I decided to purchase and install this RinParts Rin PartsSquare Type LED Reflector which I sold at Webike after all.
Motorcycle In front of it, Daylight and Blinker are lit up as Position Lamps, which is a reasonable self Appeal power, but behind Motorcycle, the tail Stop lamp is Position lamp and the Appeal force behind is too weak is.
This RinParts Rin PartsSquare Type LED Reflector Material : Quantity on Aluminum Base : Pair (for Left and Right) Quantity : 2pc. Set installed, I decided to install its Base on Rear Carrier of Motorcycle and increase the Appeal power to the rear.
In order to suppress solder peeling of the foundation by any chance due to vibration and overheating, rectify Diode (1000V1A) 1 pc. (Separately purchased 1 pc. \ 15) I put it in Wiring, but the top of the photo shows the Stop lamp lit - The bottom of the photo shows the Tale lamp lit. Especially no problem has been raised in the decrease of the light quantity and Appeal force behind.
Such a Lamp which had been installed before was supposed to be attached with the dimension to be refrained, but it was broken by a bump at the convex part of the fallen road surface and it was disconnected.
In anticipation of this, this time it is more Quantity than the previous Base width : Pair (for Left and Right) I made the dimension of 25 mm shorter, so that I did not destroy it the same way even if I overturned.
This RinParts Rin PartsSquare Type LED Reflector is a very inexpensive product, but since it is one time to replace it if it breaks it is not broken and there is nothing better to break.
This RinParts Rin PartsSquare Type LED Reflector is cheap so I am Quantity : 2pc. Set is used.
Moreover, because it seems there is no durability low because it is inexpensive, I use this RinParts Rin PartsSquare Type LED Reflector with confidence.
Installation of this RinParts Rin PartsSquare Type LED Reflector to the base part is also not difficult, it is not difficult, and although there are 3 wires, it can easily connect to a for BrakeWiring of the Motorcycle Body with the plug terminal etc. It is easy to install I think that it will belong to the category.
I attached this RinParts Rin PartsSquare Type LED Reflector and confirmed the lighting many times at night, but the Tale lamp looked like it looks like an OEM Product in the dark.
.
I found in the Package that it is for ZOOMER, so it should be able to be attached to ZOOMER
It's hard to tell the difference between Brake and Position
I couldn't pimp a motorcycle that I wanted to put on, so I left it there as a hassle It isView Detail
Go out to the night forest road etc etc etc. , Because it rides at night often, I installed it as an additional Stop lamp because it is unbearable at OEM's Small Tail lamp. I added the hole for Wiring with the same Size as the OEM Reflector and the same mounting hole diameter, and it was attached without feeling of back-end attachment.
Lights on the Stop lamp side can ensure sufficient visibility. Will not it function as a reflector?.
Lens margin etc., making is not so good, but the price is also cheap enough enough. We installed waterproof with clay in the hole where Wiring is going out.
I think that I want to Repeat if it gets broken again.View Detail
【What made you decide the purchase?】
When extending Rear Carrier exclusively for Long touring, OEMTail lamp became hard to see, so we added a round Tail lamp.
Since the mounting base was overhanging too much and broke the round Tail lamp at the time of falling, improve this time to make the overhang small and look for a cheap and easy Tail lamp in a shape other than a circle If so, I found this RinPartsSquare Type LED Reflector.
【How was it actually used?】
Immediately, I tried installing.
Although there is concern about solder attachment peeling due to vibration, for now it plays a role well in tune.
At this price, Reflector - Tail lamp - It is surprising fact that there are three functions of Stop lamp.
【Mounting was difficult?】
Material for installation : Since we used Aluminum Base, it was easy to process and the installation was Smooth.
【Please tell me the installation point and hang】
On the core of the Reverse side of this RinPartsSquare Type LED Reflector there is Φ 5 mm Bolt for mounting.
Wiring comes out three lines near one end.
And since convex for fixing Body is out near the other end, Material : A total of three holes are required in the Base of Aluminum.
Because we need holes of about Φ 5 mm each, here Φ 5. Make 3 holes in 5 mm holes in required locations.
0. Since we can afford a margin from mounting error by responding with 5 mm Large eyes hole, we will be able to install properly when we fix this RinPartsSquare Type LED Reflector.
Millimiri kitchenly and Φ 5. Although it may be processed 0 mm, it is highly likely that it will not be entered at once with experience because of experience.
If it is easy to install it in a short time, we recommend that it be mounted and processed with error margin.
[Is there anything I was disappointed about?]
As of now, it is Items which can satisfy Large about price, capacity and quality.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I do not want peeling by Solder attached by vibration.
I want you to last long.
【Have you compared items?】
It compared with RinParts Round LED Reflector.
Just because the shape was different, both price and price were the same, so this time I chose this rectangular shaped RinPartsSquare Type LED Reflector.
.View Detail
【What made you decide the purchase?】
Previously, with the Round Type LED Reflector attached, it was broken and damaged, so this time I tried this rectangular Rin Parts Rin Parts Square Type LED Reflector.
The price was also cheap, so Body was thin, so it was a product that seemed easy to install so I decided on this.
【How was it actually used?】
It seems to match the mounting base, so it looks bad.
The Reflector ability, Position and Stop lamp LED emission quantity are also good.
【Mounting was difficult?】
I did not feel difficulty in particular, but I installed it after considering the mounting dimensions and Wiring dimensions a little.
【Please tell me the installation point and hang】
Because it is a special Stop-lamp auxiliary light, we installed it to make it stand out even a little.
Also, in order to attach this Rin Parts Rin Parts Square Type LED Reflector to the Base, you have to open three Φ 5 mm holes of Wiring hole, fixing hole and rotation prevention hole.
We measure the dimensions and mark it and drill, but first open the fixation hole in the middle and pass it once, then Quantity : Pair (for Left and Right) If you reconfirm the hole position of the hole and drill it, you can install less Gap.
[Is there anything I was disappointed about?]
I installed it, but it was too normal.. I do not feel any discomfort.
It is a good thing that there is no sense of incompatibility, but it is too ordinary and it got somewhat unsatisfactory.
【Hope for Manufacturer - Please let me know if you have any improvement points]
I want this product if it has the same shape as Rin Parts Rin Parts Square Type LED Reflector and it can be used for Orange color Blinker.
【Have you compared items?】
I tried to compare with other companies' LED tail lamps, but I liked this Rin Parts Rin Parts Square Type LED Reflector at the lowest price.
[Others]
This Rin Parts Rin Parts Square Type LED Reflector is a very inexpensive product but it is a normal Tale lamp with a very Sharp feeling of elegance when trying to install it without any cheapness.
It has a lot of light at the time of light emission so it is very bright so it can be recognized very well, it is a perfect product as Tale lamp and Stop lamp.
.View Detail
【What made you decide the purchase?】
The cheapness of this RinPartsSquare Type LED Reflector = affordable price is a deciding factor.
【How was it actually used?】
There is no trouble, Position lamp and Stop-lamp are lit properly properly.
【Mounting was difficult?】
Material : I installed it on Aluminum Base
, This RinPartsSquare Type LED Reflector needed to drill three holes for Screw, Wiring, and fixed claws.
It was not difficult though it did not require too much precision, but it was just annoying.
【Please tell me the installation point and hang】
Apart from the hole for Screw, if you open it with a slightly larger grade, you can flexibly install it so you can easily install it.
[Is there anything I was disappointed about?]
This RinPartsSquare Type LED Reflector with Quantity : 2pc. Set purchased 1 pc. There was a lot of Wound on the reflective surface of.
I do not know whether the expression of disappointment is correct, but it is a fact that I felt like I was betrayed.
【Hope for Manufacturer - Please let me know if you have any improvement points]
My Motorcycle is an Off car so especially this RinPartsSquare Type LED Reflector attached to Tail will soon be full of Wounds at any rate ...
But, when it is brand new it is shock that the reflective surface is full of Wound. I want you to manage products properly.
【Have you compared items?】
Multiple companies (RinParts) Compared with the LED Reflector of the same function to sell.
But they were all Round LED Reflectors.
■ The square shows that the appearance of this RinPartsSquare Type LED Reflector is White and Red (Light is red color) There was only so, last time ● Round LED Reflector (Red) In some cases I was wearing this ■ This rectangular RinPartsSquare Type LED Reflector (Red) I selected.
[Others]
This RinPartsSquare Type LED Reflector for Motorcycle's Tail Quantity : Pair (for Left and Right) It attached to the Tail lamp's Position and Stop-lamp as an auxiliary light and it was better than the last round type for this RinPartsSquare Type LED Reflector's square ■ Tail part looks like Sharp and Parenthesis is good It became a feeling..
.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА