* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
YZF-R1 : It is attached to 2013, SizeExactly table is added, but the depth is not enough and it seems to be embedded literally when it is pushed in. So, for mounting, it is processing and mounting 120 mm of Bracket.
R1 / Although it was for R6, since it is the same shape as the base of Blinker of R25, whatever it sees, purchase daringly. There is no area to paste Double-sided Tape and to use Bolt about BlinkerBody, punch a hole in the clasp of your own Plaque at CowlReverse side (Black board under the photo) , Through Wiring and Bolt, fixed with Nut. I think that this neighborhood is an easy task for people who are engaged in Motorcycle. Made in China So the Bullet Terminal terminal is something strange, it's thin or scarce, so we have a lot of Wiring's Length so I made it again myself. Visibility seems to have no problem from the front.View Detail
For a long time I was wearing an expensive KITACO LED Tail Lamp Set, but this time, for the purpose of Imechen, ultra low price LED Tail / Blinker set (Smoke) I selected. At that time it was also at the height of Address, there were only options like KITACO and KIJIMA, so it was a very expensive shopping, but now the quality of Manufacturer is getting very good anywhere so at low prices it seems no problem at all.
For those who ride on K prior to K7 with a small amount of electricity, LEDization is a Large Change Recommendation to reduce Battery load ~ By the way, my ad is improved with full wave rectification, so it is stated that Tail is not always lighting when connected to direct current, so I was worried whether Position lamp will light, but will light with key ON. View Detail
Plus line and Minus line from Blinker were rather short. My situation, (Bandit250 LTDFirst Model Type) Both Front and Rear did not reach the vehicle Wiring, extended with Solder attached. Also, with Bullet Terminal also narrowing it is necessary to shorten the Female terminal of car Both Sides with Pliers or to re-attach the male terminal on Blinker side. Solder iron, Bullet Terminal terminal etc.. People who do not have it may need it depending on the vehicle. Body is smaller than the Small handle, brighter than the OEM (12 V 10 W ball) It is easy to see the following cars impression. I think that it is a satisfactory product for price.View Detail
R1 / Although it was for R6, since it is the same shape as the base of Blinker of R25, whatever it sees, purchase daringly. There is no area to paste Double-sided Tape and to use Bolt about BlinkerBody, punch a hole in the clasp of your own Plaque at CowlReverse side (Black board under the photo) , Through Wiring and Bolt, fixed with Nut. I think that this neighborhood is an easy task for people who are engaged in Motorcycle. Made in China So the Bullet Terminal terminal is something strange, it's thin or scarce, so we have a lot of Wiring's Length so I made it again myself. Visibility seems to have no problem from the front.View Detail
Although the product was as expected, it is a bit disappointing that the price was much higher than the NetShop of Others I bought other shops because there is no stock so there is no shower There is no particular problemView Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА