* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
OEM Screw will become unnecessary and rust will be less likely to occur so it will be extremely helpful. It is easy to maintain. The price is also cheap, so buy and there is no loss. Do not forget Grease up
I changed a lot of parts along with the brakeOH The original Pin was textured with rust This will make Maintenance a breeze One thing I was worried about, though, is that I was wondering if I could use Socket wrench, but it was no problem However, I don't know if it is 3/8 because the outer diameter of the Socket is thicker when the angle of insertion is 1/4 It is not View Detail
It exchanged simultaneously with a Brake pad.Since a authentic positive one was carrying out with the stage, the price was also expected from durability at a low price, and exchange of it was done. -- although it does not understand since the period is still short -- the durability in a Muddy -- -- I think that they are satisfying goods if good.View Detail
The brake pin looked like oem quality and fit inside the caliper perfectly. DRC products are really good, a little bit expensive. I prefer hex head instead of allen. Especially when allen tend to take over a bit after a while.Had to drill my oem ones out because they seized in my calipers and the Allen heads stripped out. Got these to replace them. The fitment was great and installation was easy. I've run them for about six rides so far and haven't seen any problems.Overall perfect fit. It looks very solid and high quality. Shipping is very fast, very well packaged. arrived in 1 weekView Detail
I bought it because the OEM came out with Stages. It looks polished and has a high quality feel, and it is stainless steel, so I expect it to be rustproof and durable. The smooth surface may also improve Pad movement.View Detail
When I did the Pad replacement, I saw that the Pin was stepped and worn. The minus on the cap of the pin was so hard that it was about to break, and I had to tighten it loosely, but if I licked it, there would be no next time.
The front brake is a replacement for another vehicle, so I decided to use the one from WR250X, considering the length of the kit.
I changed the tooling from Hexagonal to 8mm Socket and got it installed. Now I'm free from Cap worries.
I'm also worried about electrical corrosion caused by the potential difference between the aluminum caliper and the stainless pin.View Detail
These are the parts that need to be replaced from time to time because of the decrease in the number of steps. The head is 8mm in the hexagon. You can remove it with TWrench, so it's easy to maintain.View Detail
I changed a lot of parts along with the brakeOH The original Pin was textured with rust This will make Maintenance a breeze One thing I was worried about, though, is that I was wondering if I could use Socket wrench, but it was no problem However, I don't know if it is 3/8 because the outer diameter of the Socket is thicker when the angle of insertion is 1/4 It is not View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА