* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I bent the footpeg when I stood up and mangled it, so I replaced it It is installation in CB400SB of 2012 MODEL
The shape is slightly shorter on the Knee Slider, but the rest is the same look as the OEM The installation is perfectly fine, and the position is solid after installation
The OEM is a split pin installation, but this item comes with an E-Ring installation part I installed the split pin by reusing it myself
The width of the attachment part is wide, it does not enter as it is and it does not move. By the way, since the pin hole is not perpendicular to the face, Pin does not pass even if it is cut until it enters Limit (Lol) Also, the pin hole of NINJA 2 Helmet 50 OEM footpeg is beautiful whether the Reamer is passing though, but the roughness of the pin hole surface of this product is bad. Perhaps with a sharp bad Drill. After that, compared with OEM, footpeg's Rubber is fixed with Rivet so it is not possible to exchange Minus.
Up to this point there are only useless places, but the good point is that the attached Pin is hollow so it gets a little lighter (Lol) Since the rest is Rubberfootpeg, the vibration was alleviated, and the pain of the sole was also alleviated.
However, since footpeg of NINJA 2 Helmet 50 REMEM does not change much like Gold amount, I will recommend it there.View Detail
I had to replace the OEM footpeg because it broke off at the base due to a standing error in XELVIS. Aluminum casting parts are not very tenacious, so when they break, they break easily.
This one from aiNet is a bit smaller than the OEM, about 3cm wide. It looks unreliable, but it is practical enough and not so different from the OEM. However, when there is vertical movement of the ankle, such as during Shift change, the thinness of the width is exquisite and allows for smooth movement.
The price is cheap, and it is the part to buy.View Detail
I thought about looking for an OEM product, but I didn't think it would be this inaccurate, so I tried The footpegs were unnecessary because they were replaced with ones made by Takekawa, but they were not straightened when I tried them on One of them is still facing up, so I shaved it off I painted the processing part with Touch pan It is cheap, but the processing is tiring If you want to use it as it is, it's okay, but if you want accuracy, you can't use it You should buy it with the premise of processingView Detail
It was listed as inspected, but the knee slider is wobbly! Either the Screw hole was thicker or the Bolt was thinner, and it was in the bag in spotted form! I applied screw lock agent and installed it, but it fell off with a little shock It's a good thing … Also, the contents of the Rubber will be blown out, and if you step on it too hard, it will be flattened I'm disappointed I don't want to be small-mindedView Detail
When I opened it up, I found that the footpegs were both angled quite high! It took quite some time to cut with File and to make it satisfactory When it installs, Left Side seems to have gone out a little, but since there is no obstacle to operation, it does not mind Hmm If you keep on running for a little while and look at it, before you know it, the footpegRubber on the Right will be gone I did I went back the way I came and found the Rubber and found it again and it was loose enough to move by hand If you wrap the tape around the Shaft so that it won't come off, it will be about the same place as the Left Side Although you can only screw it in up to the limit, it's not going to be easy to pull out, and Quantity:Pair (for Left and Right) The Balance of the Balance has improved and I will continue to use it as it is If you care about accuracy and looks, buy the OEMView Detail
Previously, I turned on with CB 750 I lost footpeg of CB 1300 this time - - The OEM is crisp and high. (Large pattern) This Manufacturer is also good in quality and good looking. It is cheap. Good product.
(I like it) OEM's repair is cool but it is cool.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА