* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
It's not too small, but it's not too large, so I'm satisfied with it I used an LEDRelay and did not use a resistor I wanted the OEMCoupler on it rather than the resistance
Regulator end wires are too short to install. Perhaps, must cut the regulator and attach wires directly or obtain another regulator to install properly!? Have not installed yet. Regulators seem to get very hot so placement of regulators on the bike will be very important. To attach these, I might need to take my bike to the shop!?View Detail
I searched for the best one made by Yamaha and bought it because the OEMBlinker of the Racer 900GT is Bulb Type nowadays. Wiring modification is required for installation, but the Relay does not need to be replaced, just insert the included resistor in the middle. Visibility seems to be better than OEM and it is more visible to other vehicles.View Detail
Regulator end wires are too short to install. Perhaps, must cut the regulator and attach wires directly or obtain another regulator to install properly!? Have not installed yet. Regulators seem to get very hot so placement of regulators on the bike will be very important. To attach these, I might need to take my bike to the shop!?View Detail
I searched for the best one made by Yamaha and bought it because the OEMBlinker of the Racer 900GT is Bulb Type nowadays. Wiring modification is required for installation, but the Relay does not need to be replaced, just insert the included resistor in the middle. Visibility seems to be better than OEM and it is more visible to other vehicles.View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА