* Это НАИЛУЧШИЙ и ДОСТУПНЫЙ ПО ЦЕНАМ магазин для приобретения японских мотозапчастей. * Зарегистрируйтесь сейчас и получите удивительные скидки и другие выгодные предложения! *Более 2,000,000 разных товаров. Невозможно НЕ НАЙТИ нужные вам запчасти и экипировку.
ВОЙТИ В WEBIKE JAPAN
Введите ваш email от 6 знаков.
Введите действительный адрес электронной почты.
Пользователь с таким email уже существует.
Ваш аккаунт заблокирован.
Указан неверный пароль и/или Email.
Нам не удалось авторизовать Ваш аккаунт через Facebook.
Требуется ваш Email, пожалуйста введите действительный адрес email.
Поздравляем! Ваш новый аккаунт создан успешно! Теперь вы можете воспользоваться особыми привилегиями для клиентов Webike и получить наиболее выгодные предложения. Если у Вас какие либо вопросы, пожалуйста, обратитесь к нам через ОБРАТНУЮ СВЯЗЬ.
Подтверждение отправлено на электронную почту, указанную Вами при регистрации аккаунта. Если письмо не получено, попробуйте связаться с нами через обратную связь.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. Don't forget to bleed the air and refill the fluid in the MASTER after replacement.View Detail
It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to be honest. I bought it more for corrosion protection, so I'm happy with it.View Detail
I bought this as a replacement from OEM very high (Lol) Expensive for nothing. (Lol) The color of 64Titanium material of the same size is SilverTitanium and about 1000 yen. Quantity Stainless this time:2pc. I bought a set. I also bought the 64Titanium and am waiting for it to arrive! I may return this one depending on the decidedly texture!View Detail
CYGNUSxInitial Model (SE12J), if it's the same Caliper model, this The product fits I couldn't find anything that looked like a match and it was a no-go, but it was OK with no problems
It is recommended to use about 3 rolls of seal tape for water supply if possible Airtight and waterproof
The OEMs are going to be gobbling up Breeder in Rust early, but This one will free you from that worry I know it may seem expensive With this machining accuracy and if you want to replace a few of them with OEM Parts, I feel that the cost is goodView Detail
The shape of the tip is slightly different from OEM. I feel a sense of incompatibility when I put on Rubber cap.
Seal tape winds in the reverse direction, not in the tightening direction.
Noticing that Brake fluid seeped out of Caliper's Air breeder Rust was amazing as I removed it. Indeed when I thought this was dangerous, I found this product Replaced. As I wrote that the installation was to tighten Seal tape one half turn and tighten I rolled Emon's Seal tape. It looks more modest to the ground. If you think that you could buy safety cheaply in the long run as it will not rust.
By the way, by wrapping a Seal tape, it seems that it is possible to prevent the Brake fluid from bleeding out of the thread during the air removal work. I wrote it as a reference, since I did not write to absolutely roll it, I thought whether it is not necessary to wind Tape. View Detail
I've been sticking with the Tokico 6 pods. This time I adopted CaliperOverhaul and baked paint instead of OEM. I think it's a good corrosion protection. I've heard that some people use seal tape to prevent leaks, but I don't use seal tape because I have to loosen the Breeder repeatedly to keep the air out. I've had OEM jams in the past, but I'm not sure if it's because of the stainless steel. I'll have to wait and see.View Detail
The OEM Bleeder Bolt is always going to Rust and Decay, so this Material:It is safer to replace it with Stainless Steel. Be sure to bleed the air and refill the fluid in the MASTER after replacement. The Bleeder Cap was made by Straight.View Detail
ZrX1200 DAEG OEMHydraulic Clutch Bleeder Bolt This Material:I replaced it with a Stainless Steel one. The OEM Bleeder Bolt is made of steel and will always rust over time, so it's best to replace it. Don't forget to bleed the air and refill the fluid in the MASTER after replacement.View Detail
It's a little bit expensive, but I think it's not a bad idea to change it because it's a part where corrosion is a concern. It is my personal impression that the dress-up effect is not so hopeful to be honest. I bought it more for corrosion protection, so I'm happy with it.View Detail
I bought this as a replacement from OEM very high (Lol) Expensive for nothing. (Lol) The color of 64Titanium material of the same size is SilverTitanium and about 1000 yen. Quantity Stainless this time:2pc. I bought a set. I also bought the 64Titanium and am waiting for it to arrive! I may return this one depending on the decidedly texture!View Detail
Fast delivery and well packaging.Good product to replace those rusty parts.Required 2 piece for each front caliper which I have bought 4 pieces for frontView Detail
САМЫЙ БОЛЬШОЙ
МАГАЗИН В ЯПОНИИ
РАСПРОДАЖИ,
АКЦИИ, СКИДКИ
БЫСТРАЯ
ДОСТАВКА