Цепь серии VX 530VX3 [с конусным (ZJ) шарниром].

I replaced the chain on my used Ducati SS900 because it was rusty, rattly & kinked in places, and was noisy.The 520Chain can be purchased for around 15,000, yet it is firmly compatible with 1,000cc.If you use a cheap chain, you can rest assured that the Engine Displacement Volume is 600cc or less or 800cc or less.The SS900 is 900cc as the name suggests, and the power is about half of the full power 4cylinder 600cc, so even the cheap chain seems to be large and strong, but it is too late after something happens, so I decided to go with something that is properly compatible.The chain we used this time is Crimp type. There is a type of Enuma that does not need a special tool called Screw joint, but SS900 has a chain line clearance that is too tight! (Screw joint is Pin jumps out just a little bit) So I went with the normal CrimpType just in case.The results were good, Michelin's 180Tire (NORMAL is 170) then Limit will not interfere.It's not a racing model, so it's not very good, but for the price, it's a 1,000cc seal chain and it's a gold chain, so I think it's the best cost performance.It's also good for a small amount of initial growth.I would like to u...Read more

I had a chain exchanged at the shop before, but it caused trouble when I was out of town, and since then I've been exchanging chains myself.This GUARD LOCK chain tool makes it relatively easy to DIY chain cut, plate press fit and pin head tabs.I always use a grinder to grind the head down to flat before chain cutting. I don't know if I can cut well with the head as it is.If you scrape down to Flat, you can Chain cut very easily and with light force. You don't need to be stupid to do it. ＝I recommend it.Press-fitting the plate is easy as long as the proper positioning is done. The key is to carefully measure the plate width with a caliper. Once the width is measured, tighten the bolt as much as necessary, taking the bolt pitch into consideration.Pin head tsubushi is uncomfortable at first because you don't know if you are doing it right. This is the work that needs to get used to. But if you proceed carefully while checking the dimensions of the important points with Caliper, you will not fail.Thus, if you work one by one carefully, you can replace the Chain reliably even by DIY. I think it is enough performance as a tool for personal use. As for the du...Read more

I bought it thinking I wouldn't have to replace the Chain anyway, and I did. It's a bit delicate, no Repeat.good pointIt is inexpensive and easy to buy.Clip joint is also included.Easy to replace, easier to fit than the seal type.A bad pointEasy to stretch.It's not very durable, it didn't last a year.Merit is inexpensive, easy to buy, and easy to replace, but when you consider durability and elongation, etc., it goes up in price. It was a failure there.

[How is it used?Currently in use, rarely used since it only comes into play when Chain is exchanged.Was the one you received as per Image?Image is correct. It has a sense of quality and rigidity.How was your experience with it?The Grip is easy to hold, the movement of the Outer and InnerBolt is smooth, there is no stress, and the accuracy is high.Various Product Contents are made into attachments in order to be used for Chain size correspondence, Cut, and Crimp, and it is easy to use the point that the O-ring is attached to the attachment and the dropout prevention measure is given. Moreover, it is devised in the shape that can be checked so that it may not be tightened too much in the press fitting of the joint plate.When crimping the Link Plate, there is no need to prepare any other tools by using the attached Handlebar, and I like the fact that it suppresses the input of an overly large Torque. This is an excellent tool that has a lot of ingenuity and can cut and crimp reliably.There are some disappointing points such as the price, the surface coating peels off on the powder and sticks to your hand when you use it for the first time, the instruction...Read more

[How is it used?Used for Chain replacement.Was the one you received as per Image?As per Image in the product description.How was your experience with it?As per the Instruction Manual, I shaved off the head of the Chain's clasp Pin in advance. At first, I thought to shave only the clasp Pin of the side to be cut, but the Quantity:When I checked how to fix the Set, I decided to cut both of them in order to do it surely because it is only compressed by Bolt.Quantity:When setting, there is a positioning function, and once the hang is grasped, Quantity:Set is easy.There are two types of cut bolts, one with a short pin end and the other with a long pin end, which must be used to cut the diaphragm pin. First, use the short pin end to push out the diaphragm pin to some extent, and then replace it with the long pin end.The short pin tip was fine, but the long pin tip was shaky because the center of the shaft was not out.The pin tip was shaky, so I was worried about whether I could push it out well, but it didn't lead to a large problem, and it did work.It's a shame because it was otherwise good.It's a consumable item and the price is low, so I'm willing to acce...Read more