・Fuel control for each individual cylinder in a smaller enclosure
Регулировка топлива при разогреве (устройство считывает температуру двигателя и позволяет регулировать топливо/время на основе показаний).
・Reduced size from the PCIII USB
・Easy to install
・USB powered from computer;9 volt adapter is no longer needed
・Two-position map-switching function built in
・Can add any Single Pole Single Throw (SPST) switch and toggle between two different fuel maps
・Gear/speed input allows for map adjustment based on gear
・Analog input allows user to install any 0-5 volt sensor
・Build an adjustment table based on analog input such as boost or temperature
・Power Commander V is capable of allowing each cylinder to be mapped individually and for each gear with the gear position input connected
・More tuning ranges than PCIII USB
Усовершенствованная утилита "ускорительного насоса
・For Offroad and ATV, see appropriate catalog under Moose Power Commanders
・Made in the U. S. A.
SECONDARY FUEL MODULE
・Allows for the use of the Dynojet Quick Shifter sensor on eight-injector bikes which provides added fuel control and shifter functionality
Если вход положения редуктора подключен к Вашему PCV, то Вы можете настроить все форсунки по принципу "на редуктор".
・Allows for the adjustment of all eight-injectors
・See application chart for availability
・Single cable connection to the PCV
・Connects to the upper injector rail using OEM connectors
・You can also map each injector separately, giving you up to 48 complete maps
Базовый" режим позволяет иметь один топливный стол, который просто помещает запрашиваемую смену топлива одновременно в верхний и нижний инжекторные модули. в то же время
・Adjust both upper and lower injectors by as much as +250/-100%
Базовый" режим - это идеальная настройка для модифицированных двигателей, требующих больше топлива, чем могут обеспечить четыре инжектора, но не нуждающихся в сложности отображения каждого цилиндра и каждой передачи в отдельности. Базовый" режим является идеальной настройкой для модифицированных двигателей, которые требуют больше топлива, чем могут обеспечить четыре инжектора, но не нуждаются в сложности картирования каждого цилиндра и каждой шестерни в отдельности.
QUICK SHIFTER EXPANSION MODULE
・The QEM allows the Dynojet Quick Shifter sensor to be used with Power Commander V on bikes that have eight injectors
・Once the sensor is attached you will have full Quick Shifter functionality
・The QEM connects to the upper injectors and then into the PCV
[Перевод.]
Контроль топлива для каждого отдельного цилиндра в небольшом корпусе
Регулировка расхода топлива при разогреве (устройство, которое считывает температуру двигателя и позволяет производить регулировку расхода топлива/времени на основе показаний).
Сокращение размера с PCIII USB
Простота установки
USB поставляется с компьютера; 9-вольтовый адаптер больше не нужен
Встроенная 2-позиционная функция переключения карт
Для переключения между двумя разными топливными картами добавляется однополюсный одноболтовый переключатель (SPST).
Зубчатый/скоростной вход позволяет регулировать карту на основе редуктора.
С помощью аналоговых входов могут быть установлены датчики 0-5В.
Создайте таблицу настройки на основе аналоговых входов, таких как повышение или понижение температуры.
Командующий V может составить карту каждого цилиндра по отдельности..
Больше диапазона настройки, чем PCIII USB
Усовершенствованная утилита "ускорительного насоса
Для бездорожья и квадроциклов, пожалуйста, обратитесь к соответствующему каталогу Moose Power Commanders..
Сделано в США
Вторичный топливный модуль
Dynojet Quick Shifter Sensor может использоваться на 8 инжекторных мотоциклах для обеспечения дополнительного контроля топлива и функции переключения.
Если вход положения редуктора подключен к ПЛК, то в "редукторах" можно настроить все форсунки.
Все 8 форсунок могут быть отрегулированы.
См. доступные диаграммы приложений
Одно кабельное соединение с PCV
Соедините с верхней направляющей инжектора с помощью штатного разъема.
Каждый инжектор может быть нанесен на карту отдельно, чтобы заполнить карту до 48 инжекторов.
В режиме "Basic" можно подготовить один топливный стол, который будет подавать требуемую смену топлива одновременно на верхний и нижний инжекторные модули.
Вверх / Вниз инжектор + 250 / -100
Базовый" режим - это идеальная настройка для модифицированного двигателя, требующего больше топлива, чем четыре форсунки, но не требующего сложности отображения каждого цилиндра и каждой передачи в отдельности.
QUICK SHIFTER EXPANSION MODULE
QEM позволяет использовать датчик Dynojet Quickshifter вместе с Power Commander V на мотоциклах с восемью инжекторами.
После установки датчика можно использовать всю функциональность Quick Shifter.
QEM подключается к верхнему инжектору, а затем к PCV.
・Fuel control for each individual cylinder in a smaller enclosure
・Warm-up" fuel adjustment (unit reads engine temp and allows fuel / timing adjustments based on the reading)
・Reduced size from the PCIII USB
・Easy to install
・USB powered from computer; 9 volt adapter is no longer needed
・Two-position map-switching function built in
・It can add any Single Pole Single Throw (SPST) switch and toggle between two different fuel maps
・Gear / speed input allows for map adjustment based on gear
・Analog input allows user to install any 0-5 volt sensor
・Build an adjustment table based on analog input such as boost or temperature
・Power Commander V is capable of allowing each cylinder to be mapped individually and for each gear with the gear position input connected
・More tuning ranges than PCIII USB
・Enhanced “accel pump" utility
・For Offroad and ATV, see appropriate catalog under Moose Power Commanders
・Made in the U.S.A.
SECONDARY FUEL MODULE
・Allows for the use of the Dynojet Quick Shifter sensor on eight-injector bikes which provides added fuel control and shifter functionality
・If gear position input is connected to your PCV, you can adjust all of the injectors on a “per gear" basis
・Allows for the adjustment of all eight-injectors
・See application chart for availability
・Single cable connection to the PCV
・Connects to the upper injector rail using OEM connectors
・You can also map each injector separately, giving you up to 48 complete maps
・The “basic" mode allows you to have a single fuel table that simply puts the requested fuel change in both upper and lower injector modules at the same time
・Adjust both upper and lower injectors by as much as +250 / -100%
・The “basic" mode is the perfect setting for modified engines that require more fuel than four-injectors can provide, but do not need the complexity of mapping each cylinder and each gear separately
QUICK SHIFTER EXPANSION MODULE
・The QEM allows the Dynojet Quick Shifter sensor to be used with Power Commander V on bikes that have eight injectors
・Once the sensor is attached you will have full Quick Shifter functionality
・The QEM connects to the upper injectors and then into the PCV
[Translation]
・Fuel control for each individual cylinder in a small enclosure
・Warm-up fuel adjustment (a unit that reads engine temperature and allows fuel / timing adjustments based on the reading)
・Size reduction from PCIII USB
・Easy to install
・USB supplied from computer; 9 volt adapter is no longer needed
・Built-in 2-position map switching function
・Single Pole Single Throw (SPST) switch is added to switch between two different fuel maps
・Gear / speed input enables gear-based map adjustment
・Using analog inputs, 0-5V sensors can be installed
・Create an adjustment table based on analog inputs such as boost or temperature
・The Power Commander V can map each cylinder individually.
・More tuning range than PCIII USB
・Enhanced "acceleration pump" utility
・For Offroad and ATV, please refer to the appropriate Moose Power Commanders catalog.
・Made in USA
Secondary Fuel Module
・Dynojet Quick Shifter Sensor can be used on 8 injector bikes to provide additional fuel control and shifter function
・If the gear position input is connected to the PCV, all injectors can be adjusted in "gear units"
・All 8 injectors can be adjusted
・See the available application charts
・Single cable connection to PCV
・Connect to the upper injector rail using the OEM connector
・Each injector can be mapped separately to complete a map of up to 48 injectors
・In the "Basic" mode, a single fuel table can be prepared that will feed the requested fuel change to both the upper and lower injector modules simultaneously
・Up / Down Injector + 250 / -100
・The "basic" mode is the perfect setting for a modified engine that requires more fuel than four injectors, but does not require the complexity of mapping each cylinder and each gear separately
QUICK SHIFTER EXPANSION MODULE
・The QEM allows the Dynojet quickshifter sensor to be used with the Power Commander V on motorcycles with eight injectors
・Once the sensor is installed, the full functionality of the Quick Shifter can be used
・QEM is connected to the upper injector, and then to the PCV