KAWASAKI Z1 (900 Super Four) Мото обвес

I was worried about OEM, but I chose this one because it is with key
Exactly the same shape as the OEM, the only difference is the length of the screw in picture 1

Installation is also ...

I was astounded at the quality of the package (steel tank and ABS sidecovers & tail piece). I doubt if I could have restored my originals to the same level. The delivery time was great - 12 day...

No!
Is the 3 thicker part of the body's mounting pin attached short?
We can't fix it at all!
I threw the gold into the trash, sir

I took it off the front exterior and eventually i...

I bought it when I was OHing my Carburetor, and like the OEM, the thickness of the Washer Because of the thinness of the material, it will inevitably become distorted over time
So I installed ...

It is impossible to install with ordinary people after opening products after delivery.
First I did not write any explanation of whether processing by experts is necessary.
It's the wor...

Although it is for another car model, I purchased this Grommet as Size matches. quality ? Accuracy etc. There is no problem at all, it can be used normally. When attaching to the car body, Rubber...

Before purchasing DOREMI's Emblem this time I used cheap Emblem. The color was Yellow sexy and it was thin and cheap texture was rolled out with LePera. DOREMI's Emblem is expensive but i...

The four points of the star are not within the position of the OEM Tail lamp.
D1 as ZEPHYRSpec. It is Items necessary to make it ^ ^

I kept it, but whether the surface treatment was bad or not, it rusted in a flash. I bought Engine cover bolt, but that is the same.

I bought DOREMI's Tank and challenged while Scale as much as I could depend on feeling while looking at the pictures.
It worked on our own. There are some errors, Motorcycle is Quantity : ...

Tank Bagetc. bought it because I don't want to use it.

It was difficult to install but I am satisfied.

SecurityGoods and in-vehicle tools, etc. are included.

I bought it because I want to use the Grab Bar in its original mounting position after lay-down
The hole you can't see in the picture is tapered inside I don't know why it is tapered and it is...

Because I purchased the Rear Sets which cannot be attached to the Kick pedal, I installed it To protect the Shaft from rust, Silicon grease is applied to it

When I went to install it, I saw that there were a few pins missing. The pins that came with it are all there, but they should be locked in place
I couldn't install it because it doesn't have ...

Side cover Grommet's
Rubber has deteriorated
I bought it as a spare

Compared to OEM parts, the
Grommet's Rubber was too soft
It is easier to remove the side cover lightly
I'...

For installation, masking the tank firmly and pin punching the pin (I would struggle without it.) so
It's hammered in About 30 minutes in and out

When I took the Tank off, I noticed that there was one missing Rubber and bought it (I mean, I bought it at Point, so it was free) It's indistinguishable from the OEM, or is it the same?
There...

Although it was impressive that honest making is coarse as for the person who purchased initial sales! LtdOEM could not find it but purchased it without any help
Plating glue was also good, th...

OEMParts is not used as a result of deterioration, purchased by preventing falling off of Side cover.
Soft and Fit feeling is also good.
RiproParts should be easy to get out of print. After...

Even though Pin is too thick to cut the hole on the Tank side, Cap does not open at all after installation. The lowest item. I can not use it because it will not open unless I hit it with Hammer....

We have seen many cases where the motorcycle parts are made in China This product is odorless This product is odorless, and I was able to install it on my bracket without any problem It is safe t...

It's not available in Kawasaki OEM Parts anymore If you don't have these small rubber parts, you can use the number bracket It's loaded with vibrations; the quality of the Rubber is good and help...

Great looking seat good quality materials used , Not designed to fit a KZ900 is listed for Z1 made some mods to base for proper fit . Foam is a little on the soft side for my weight 130kg .

I think that it is a very good product. Design, finish of welded part, finish of Plating, I think that the accuracy is excellent anyway. It is still strong Tandem bar.

another excellent product, while these rubbers are a simple item, when you need 'em, you need 'em, these items are just the same as the originals, the quality is good, they fit right and they are...

Material is ABS as opposed to OEM. ProductNo is registered as MRS, but the contents are made by D company and are also engraved. As a feeling of use there is no problem within OEMTail and there i...

The manufacturing precision of an Engine of exterior equipment is perfect at any rate for the Z which is not so high.Although tightness of a sheet may be delicate at individual specificity, since...

Although it was a ball of pure fire usually, he bought Mr. M-TEC's exterior Set so that the exterior could be changed in feeling.
The result is quite good. Probably, it does not turn out t...

It used for Z1. Since the crevice was somewhat large when an Ornament was attached when then used, some Bolts and Spacers were cut and attached. The attachment in those without
> proces...