HONDA MONKEY Подвеска / Подножки / Колеса / Маятники

[How is it used?
I have an XJR1300C from MainMotorcycle with Over Rear Sets, Shift pedal and Brake pedal.
I installed it because the TipRubber was losing steps, the feeRing was getting wors...

I saw that someone had commented on this and I copied it.
It was attached to baby face's Rear Sets.

We purchased this one because we naturally need a rubber to replace the pedal end of the pedal. I am very grateful for the low price.

It was very difficult to fit the thick rubber as it wa...

In the case of Brake, you only step on the brake, so if it doesn't slip, you don't need to worry about the rubber and its deterioration.
The end bar here is a little longer, so it is easier to...

The installed product was scratched, so we replaced it with this new one.
It's a good thing that it's sold as a Single Item so I can exchange it for a new one.

I bought a used KSR80 from a private seller, but the footpeg, shift pedal and footpeg were rusted badly. Universal Material:I did the dress-up with aluminum, but I couldn't use the universal prod...

I mounted the full gcraft rims on my monkey baja. As always top quality! Just a pity that there is no 3.0 version available

Gcraft steady straps are of very good quality. They have a lot of grip, even when it rains and that makes them interesting. I can't upload a picture but I can deliver them by mail, also for my o...

I mounted the silver version on 1 of my monkeys. Very nice finish and perfect fit. You can go up to 3 wide at the front, 3.5 at the back. I can't upload a picture but I can deliver them by mail...

I mounted the +16 version on my tuning baja. Nice finish but I give 4 stars because of the higher price. I can't upload a picture but I can deliver them by mail, also for my other reviews WEBIK...

For those who have difficulty in riding posture with tight rear sets such as MONKEY's 180mm back, this 150mm rear set is easy to ride.

The 4-position change allows for fine tuning in case ...

Swing Arm also needs to be modified according to CustomManufacturer's Spec.
We have rebuilt a part of KEPSPEED's Swing Arm to be able to carry it with reinforced plates.
I'm sure this price...

Installed on GORILLA.
I'm doing just that! I was looking for a black one that didn't stand out because I didn't want it to be a
It's as plain as the image.
I'm sure everyone has differen...

It is fastened together with Pivot bolt of Swing Arm, so it can be installed very Firmly.
However, once you need to pull out Pivot bolt, you need Jack-up.
There is a support plate to be mou...

Looks, texture, feeling of use, I think it is very good. I think that it is an excellent article without loss by purchasing.
On the premise that it is good, if I give you anxious points
- I...

I was prepared for this because the Gold amount is extremely low compared to JAPAN.
The Rim is not shiny and there is BALI around the Wheel, just as I expected.
BALI was lightly polished wi...

I disliked 5LMONKEY's Fork Dust Boots, so I bought them during Restore.
There is no Installation Manual, and I thought I could change the color later.:Pair (for Left and Right) Disassemble the...

It can be attached to CHALY! Moreover, the screw is an anti-loosening screw, so you can go touring with peace of mind!

3.5j
The Center of the Large body comes out both front and rear by pontooning, but there is some flex when you rotate it.
That's the Chinese, BALI is terrible.

Although it is said to be compatible with the MONKEY, in reality, it interferes with the chain case cover of the STD of AB27 and Z50J and cannot be installed without additional processing with a ...

I used it on my '88 GORILLA.
I changed to Aluminum Cast Wheel, so I installed it to Center out.
Because the material is not aluminum, I think that it is a little heavy, but I use it in Tour...

I drilled a hole on the opposite side of the original hole in the bracket of the brake switch, and changed the bolt where the spring of the brake switch would be applied. Spring of the switch and...

Consider each Manufacturer of CFCFork in HondaGORILLA.
The domestic manufacturer's was unusually high and could not be bought very much.
This product was also out of stock and hard to find,...

I used it as a substitute for OEM, but I am satisfied with the cheap price for the same etc. as OEM.

I used it for my first MONKEY assembly, I don't know the OEM and I'm happy with the texture.