HONDA MONKEY Мото обвес

I bought it for a custom tank in black and sprayed Rainbow Lame on it to give it an austere MONKEY look.

I bought this for my custom tank in black with Rainbow Lame on top.

Purchased to install Takegawa zStyleFender on my MONKEY4L.
I recommend you to make your own Bracket because it is ugly!

First of all, I bought it because it is cute. I was able to install it with no problems.

Worst case scenario, TankLiner and paint were scheduled, but the interior was rusted and I had to start with rust removal.
It is roughly made and needs to be put in the Pate. Incidentally, GOR...

Paint was a little rough for cost performance.

I didn't have high expectations since it was a Chinese product, but I thought I'd be satisfied with the rust-free, well-painted finish.
The MONKEYOEM tool box could not be attached without mod...

4LMONKEY is already discontinued, so it is difficult to get m (__) m
In such a situation, this item is a 4LOEMTank looking onigiri tank except for the Cap, so I bought it! Even though it's bra...

It is a helpful product that is sold only in Tanaka. If you have this, you can install Rear Fender on 5LMONKEY and 4LTail! (°∀°) BALI ass confirmed! (* 'ー `*)

This is one of the few Chinese Tanks that can use 5LOEMCap.
Tank cap (Garbage), Cook and Spacer are included, and you need to be careful not to damage the screw holes on the frame.
Please n...

It was used during Conversion to 12v.
Material:Aluminum and lightweight w
I bought it because I wanted to be concerned about what I couldn't see.
I like it, although I am disappointed th...

It is EXACTLY when it is set to Rear carrier-less.
I think it is good because it gives the impression that the buttocks have been raised.
I like the length and angle, which is not often see...

About quality and texture It's great. About the feeling of use The quality was good, and there was no problem installing it Products to buy together M6 bolt , m6 nut Difficulty of installation...

I bought it to fill the empty space under the seat on the Right Side of the car body, which was left open because of the Other Brand ProductExhaust System.

The empty space can be filled wi...

I installed this product because the OEM side cover mounting holes were rotted and no longer usable.
The design and texture are perfect, but it is a little disappointing that when the Seat is ...

I renewed the ROD when I lengthened the Shift rod, and I also renewed the Nut while I was at it.
Since it is a Stainless Steel ROD, it must use a Stainless Steel Nut or it will be Rusty.... Прочитайте больше

I'm not sure if I'd like it if it was a little taller.

should have asked before but this will not fit on a 2022 Honda Monkey Quality item tho. its built solid and is very good craftsmanship. I will have to build some brackets for it.

When customizing the front of the DAX, you can use the Stabilizer Type 1 and
Quantity:I used it in Set.

Because Size is Size, there is almost no original Front Fender function, but
T...

I used it with the SHIFT UP 6cm Long Swing Arm
I gave it 4 stars for quality and texture because there was a little BALI
However, there is no problem to use

Recommended!
OEM is expensive so …
Replaced front and rear!
It looks great!

Aluminum so I can adjust the light intensity to my liking!
I wanted to make it Classic and it is very good.
Higher grade feeling

It is totally different with it on and without it off.
You can feel your buttocks cool and breezy.
Even after parking the bike in the hot sun, the Seat is no longer too hot.
A side effec...

The material is made by Mukawa, so it's solid.:I think it's better to be thicker than OEM with aluminum I think it should be a little longer

About quality and texture I was satisfied with the color About the feeling of use It can give off color and is marked on/off properly Products to buy together be not in Difficulty of installat...

The design is so complete that at a glance you would think it was OEM.
The mounting position on the Swing Arm of 5LMONKEY is also Exactly.
The standard Bolt will rust out after a month or s...

I had been planning to put them on for some time because my buttocks were sweating and steaming from long-distance touring.
Steaming was actually eliminated considerably after using the produc...

I had been thinking of putting them on for some time because my buttocks were sweating and steaming during long-distance summer touring.
I was not sure which product to choose, but I decided t...

I am using it on my CT110 HUNTER CUB. As rumored, the OEM Seat is a pain in the butt when driving for long periods of time, and I considered various options such as Gel Zabs, but I did not want t...

After installation, I did a day-touring trip of about 500 km.
(*CROSSCUB110, replaced by Seat of JA45.)
Having previously used a similar product made by Komine, I leave you with my comparat...